Free USA Domestic Shipping over $99
Align RC 6 Channel Helicopter T-REX 700E F3C V2 Super Combo KX018E11A ARF
  • Align RC 6 Channel Helicopter T-REX 700E F3C V2 Super Combo KX018E11A ARF
Item# 15H-KX018E11A-700E-F3C-V2-SuperCombo-ARF


This item is currently out of stock!

Specification(GP900 Head lock gyro combo) :
1.Utilizes MEMS(Micro Electro Mechanical Systems) micro electronic sensors which are small, highly reliable, and highly stable.
2.16bit high processing speed CPU is used for ultra high resolution, resulting in higher rudder precision than previously possible, even on modern high powered helicopters.
3.Supports Spektrum and JR satellites, traditional receiver not needed.
4.Support Futabs S-BUS system.
5.Support both digital and analog servos.
6.Support both wide and narrow band receivers.
7.Integrated RCE-G600 speed governor function, thus GP900 can provide speed governor function without additional electronics.
8.Suitable for all 200 to 700 size glow engine or electric helicopters, with higher vibration resistance than any other systems. Superior performance is achievable even with harder mounting foam tapes.
9.Support parameter setting through PC interface, as well as firmware updates.
10.Anti-torque compensation. Optimal tail locking achievable no matter if gyro is mounted upright or inverted.

Specification(T-REX 700E F3C V2) :
1.Brand new all metal high precision and high rigidity main blade assembly, providing 3 positive/negative deltas andnumerous Bell & Hiller mixing ratios.
2.Innovative sliding battery tray rails imbedded into the 3K side frames, with patented spring loaded latching mechanism, allowing for quick battery access as well as battery protection.
3.Precision CNC machined aluminum pieces including elevator servo mount, rudder servo mount, rudder control bell crank arm, vertical and horizontal fin mounts.
4.Top mounted motor base allowing blade drafts to cool the motor effectively.
5.Newly designed one piece stainless steel main gear hub to improve rotational stability.
6.Utilizes highest spec CNC modue-1 helical main gear, with highest load tolerance and lowest noise.
7.Motor mount consists of third bearing block to provide motor shaft support, effectively reduce torque induced shifts,and minimize gear striping issue.
8.Top mounted ESC platform to take advantage of main blades airflow for effective cooling.
9.Innovative sliding battery tray rails imbedded into 3K side frame, providing easy battery access and protection.
10.Brand new CNC machined metal tail gear box, with thicker side plates to increase rigidity. The more streamlined design also allows for simpler disassembly.

Users must have a certain concept of security to operate the R/C helicopters.
Be sure to read and comply with related safety notes of instruction manual before flying.

Specification(GP900 Head lock gyro combo) :
  • Operating Voltage:DC 3.5~8.4V
  • Current Consumption:<80mA @ 4.8V
  • Angular Detection Speed:600 degrees/sec
  • Operating Humidity:-20℃~65℃
  • RoHS certification.
  • Operating Humidity:0%~95%
  • Size:36.5x25.2x15.6mm
  • Weight:11g

  • Specification(T-REX 700E F3C V2) :
  • Length: 1343mm
  • Height: 424mm
  • Width: 210mm
  • Main Blade Length: 700mm
  • Main Rotor Diameter: 1582mm
  • Tail Rotor Diameter: 281mm
  • Motor Drive Gear:12T
  • Main Drive Gear:112T
  • Autorotation Tail Drive Gear: 104T
  • Tail Drive Gear: 24T
  • Drive Gear Ratio: 1:9.33:4.33
  • Weight(With Motor): 3230g
  • Flying Weight: Approx. 5200g

  • Accessories:
  • T-REX 700E F3C Kits Set X1
  • Aluminum Tail Boom X1
  • 3K Carbon Fiber Tail Boom X1
  • F3C 700mm Carbon fiber blades X1
  • DS610 Digital servoX3 set
  • DS650 Digital servo X1
  • GP900 Head Lock Gyro X1
  • 700MX Brushless Motor(470KV) X1
  • Castle ICE2 HV 120 Brushless ESC X1
  • 6A External BEC w/ 5.1V Two-way Step-down voltage regulator X1
  • 105mm 3K Carbon Fiber Tail Blades X1 Set

  • Radio transmitter and electronic equipment required for assembly:
  • Transmitter(7-channel or more, helicopter system)
  • Receiver(7-channel or more)
  • 6S Li-Po 4500 ~ 5200mAh X2
  • Dial Pitch Gauge

  • ************************************************************************************************************************************

    We appreciate you choosing us for all your RC helicopter needs. Please note that all requested returns and exchanges with Align products will subject to a 15% restocking fee. Any tampered, used, damaged product will not be permitted for an exchange or return.

    Upon receiving any Align product, please inspect the product or items before opening the package. If an item or part is defective upon arrival, please contact Align.
    Align USA would like to provide all technical support for their products. You can contact Align USA at:
    Assurance R/C USA
    Tel: 562-598-4700
    Fax: 562 598-4702
    Thank you and we appreciate your business.


    Align Trex 700 F3C Spare Parts
    700 F3C Painted Canopy HC7602
    Price: $110.38
    Damper Rubber 80?X HN7024A
    Price: $5.31
    Out of stock
    F3C Carbon Stabilizer/2.0mm HN7029A
    Price: $35.90
    F3C Metal Control Lever/Black H70002QA
    Price: $53.19
    F3C Metal Control Lever/Silver H70002QF
    Price: $53.19
    F3C Metal SF Mixing Arm HN7012A
    Price: $30.58
    F3C Metal Washout Control Arm HN7011A
    Price: $30.58

    Customers Also Bought These Best Sellers

    Lipo Application Guide
    Best Price Guarantee